People like to call this Fake...not true!

Tifferau was a French chemist converted to alchemy, or rather that landed alchemy as a point of arrival (but looks a little!)
its theoretical and its practical experience. After traveling along wide for 5 years in mines, quarries, Ganges, metalliferous veins
managed to get gold for transmutation.

Have not yet been tested in the laboratory for what I know. If someone wants to try it can not hurt!

I carry the as they are written in the book.

Put in a bottle containing 8 g to 10 g of fine silver filings, cover with nitric acid and sunning.

It will have the development of nitrous gas and the formation of a black deposit, aggregate on the bottom. Leave the bottle

to stand for twelve days, then add distilled water to the boil until the seventeenth day

of nitrous vapors, then heated up to the total dry matter appears black and greenish. Of this compound,

pour boiling nitric acid several times: you will get darker than green, then yellow and finally golden, at which time the

material breaks down and reveals the gold flakes.


It has also written another of "recipe" that the following:

Stir twelve parts of concentrated sulfuric acid and two parts of nitric acid at 40 ° C. This mixture should be placed in glass tubes in which it will be paid

filings silver and pure copper, in a mixture in which the copper comes in for a tenth. Bring to the boil for several days by adding sulfuric acid and pure

concentrated, add sulphate of ammonia and bring back to a boil.

Decant the nitric solution of the tubes and boil the remainder of nitric acid with sulfuric acid in the amount of 10.12 times the volume of the first acid.

Heat to 360 ° C. for 36 hours after cooling the mixture deposited gold particles precipitable with oxalic acid.

http://www.energeticforum.com/renewable-energy/13372-produce-gold.html

So i have here the strychtine poison, who killed Alexander the Great, and Socrates! ok, this is available at homeopatic medicine...usually used as 5 grains a day, the deadly fatal dose is 30 grains!

IT KILLS IN 15 MINUTES...

you use this homeopatic medicine, for depression, but also...for those old ladies who suffer a lot from cold weather!!!!

AND THE OLD BITCH TOOK ....Boney M ~ One Way Ticket (HQ)

"A few teaspoons of methanol can cause blindness and a few tablespoons can be fatal"

Elsa David the perfect plan DEBKAfile would be...giving her this tablets steroids to the gym fitness

welcome back to war! "Contact with the liquid pure form can cause death within hours, as nicotine passes through the dermis and heads directly for the bloodstream" "Nicotine is readily and easily absorbed through the skin. The LD50 (LD50=dose that will kill 50% of those exposed) for nicotine in a nontolerant individual is about 60-75 mg....I remember reading some thriller story years ago which hinged on an otherwise inexplicable air-crash. The murderer/terrorist had painted pure nicotine onto one of the controls of the aircraft, a control that would only be touched just prior to landing. Pilot touches the button, and hey presto is dead in seconds by skin absorption..."

I'm starting the weekend with powerfull deadly toxins...begging with Dogoxin

LANOXIN

https://www.drugs.com/uk/lanoxin-0-125mg-tablets-leaflet.html

Elsa David as u monitor NSA - National Security Agency the difficult part is...find the substance on the world market..because its not just simple typing digoxin...

Gosto · Responder · 4 h

Elsa David so...i have to turn around and around to get another name for it Central Intelligence Agency (CIA) ...and search for : Chloroformic digitalin

So speacking about perfet murders..and getting away from the gov. mail box

Oxalic acid poisoning

    

Oxalic acid is a poisonous, colorless substance. This article discusses poisoning from swallowing oxalic acid.

https://medlineplus.gov/ency/article/002479.htm

which is very sweet flavour it goes well in any cake ....

http://www.ebay.co.uk/itm/12-5kg-oxalic-acid-Hull-Deck-GRP-cleaner-stain-rust-remover-/192061350958

that we want to track an android on a first step, we have the number, and we want to know its location...just to check it if is on a rail station..or on the airport bathroom

LocationManager

public class LocationManager 
extends Object 

java.lang.Object
↳	android.location.LocationManager

---

This class provides access to the system location services. These services allow applications to obtain periodic updates of the device's geographical location, or to fire an application-specified Intent when the device enters the proximity of a given geographical location.

You do not instantiate this class directly; instead, retrieve it through Context.getSystemService(Context.LOCATION_SERVICE).

Unless noted, all Location API methods require the ACCESS_COARSE_LOCATION or ACCESS_FINE_LOCATION permissions. If your application only has the coarse permission then it will not have access to the GPS or passive location providers. Other providers will still return location results, but the update rate will be throttled and the exact location will be obfuscated to a coarse level of accuracy.

https://developer.android.com/reference/android/location/LocationManager.html#NETWORK_PROVIDER

RFID 13.56 MHz / NFC Module for Arduino and Raspberry Pi

I NEED A PEER-T-PEER CONNECTION ON STACK...I NEED TO DISARM THE SECURITY ALARM WITH A TOKEN CRACKER...

/*  
 *  RFID 13.56 MHz / NFC Module
 *  
 *  Copyright (C) Libelium Comunicaciones Distribuidas S.L. 
 *  http://www.libelium.com 
 *  
 *  This program is free software: you can redistribute it and/or modify 
 *  it under the terms of the GNU General Public License as published by 
 *  the Free Software Foundation, either version 3 of the License, or 
 *  (at your option) any later version. 
 *  a
 *  This program is distributed in the hope that it will be useful, 
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of 
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the 
 *  GNU General Public License for more details.
 *  
 *  You should have received a copy of the GNU General Public License 
 *  along with this program.  If not, see http://www.gnu.org/licenses/. 
 *  
 *  Version:           1.0
 *  Design:            David Gascón 
 *  Implementation:    Ahmad Saad & Javier Solobera
 */

uint8_t dataRX[35];//Receive buffer.
uint8_t dataTX[35];//Transmit buffer.
uint8_t _UID[4];// stores the UID (unique identifier) of a card.
uint8_t keyAccess[] = {0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF } ;// stores the key or password.
uint8_t address = 0x04;//Address to read.
uint8_t ATQ[2];//Answer to request
uint8_t state;//state of the process
uint8_t aux[16];//Auxiliar buffer. 

void setup()
{
 //Start serial port 115200 bps:
 Serial.begin(115200);
 delay(100);
 Serial.print("RFID/NFC @ 13.56 MHz module started");
 delay(1000);
 //!It is needed to launch a simple command to sycnchronize
 getFirmware();
 configureSAM();
}

void loop()
{
 Serial.print("\n");
 Serial.println("Ready to read...");
 /////////////////////////////////////////////////////////////
 //Get the UID Identifier
 init(_UID, ATQ);
 Serial.print("\n");
 Serial.print( "The UID : ");
 print(_UID , 4);
 /////////////////////////////////////////////////////////////
 //Auntenticate a block with his keyAccess
 state = authenticate(_UID, address, keyAccess);
 Serial.print("\n");

 if ( state == 0) {
  Serial.println("Authentication block OK");
 } else {
 Serial.println("Authentication failed");
 }
 /////////////////////////////////////////////////////////////
 //Read from address after authentication
 state = readData(address, aux);
 Serial.print("\n");

 if (state == 0) {
  Serial.println("Read block OK");
 } else {
  Serial.println("Read failed");
 }

 Serial.print("\n");
 Serial.print("Data readed : ");
 print(aux , 16);
 Serial.print("\n");
 delay(2000);
}
//**********************************************************************
//!The goal of this command is to detect as many targets (maximum MaxTg)
// as possible in passive mode.
uint8_t init(uint8_t *UID , uint8_t *ATQ)   //! Request InListPassive
{
  Serial.flush();

 dataTX[0] = 0x04; // Length
 lengthCheckSum(dataTX); // Length Checksum
 dataTX[2] = 0xD4;
 dataTX[3] = 0x4A; // Code
 dataTX[4] = 0x01; //MaxTarget
 dataTX[5] = 0x00; //BaudRate = 106Kbps
 dataTX[6] = 0x00; // Clear checkSum position
 checkSum(dataTX); 

 sendTX(dataTX , 7 ,23);

 for (int i = 17; i < (21) ; i++){
  _UID[i-17] = dataRX[i];
 UID[i-17] = _UID[i-17];
 }

 ATQ[0] = dataRX[13];
 ATQ[1] = dataRX[14];

 if ((dataRX[9]== 0xD5) & (dataRX[10] == 0x4B) & (dataRX[11] == 0x01)) {
  return 0;
 } else {
  return 1;
 }
}
//**********************************************************************
//!A block must be authenticated before read and write operations
uint8_t authenticate(uint8_t *UID, uint8_t blockAddress, uint8_t *keyAccess)
{
 dataTX[0] = 0x0F;
 lengthCheckSum(dataTX);
 dataTX[2] = 0xD4;
 dataTX[3] = 0x40; // inDataEchange
 dataTX[4] = 0x01; //Number of targets
 dataTX[5] = 0x60; // Authentication code
 dataTX[6] = blockAddress;
 for (int i = 0; i < 6 ; i++) {
  dataTX[i + 7] = keyAccess[i];
 }
 dataTX[13] = UID[0];  dataTX[14] = UID[1];
 dataTX[15] = UID[2];  dataTX[16] = UID[3];
 dataTX[17] = 0x00;
 checkSum(dataTX);
 sendTX(dataTX , 18 ,14);

 if ((dataRX[9]== 0xD5) & (dataRX[10] == 0x41) & (dataRX[11] == 0x00)) {
  return 0;
 } else {
  return 1;
 }
}
//**********************************************************************
//!Write 16 bytes in address .
uint8_t writeData(uint8_t address, uint8_t *blockData)  //!Writing
{
 Serial.print("                ");
 dataTX[0] = 0x15;
 lengthCheckSum(dataTX); // Length Checksum
 dataTX[2] = 0xD4;
 dataTX[3] = 0x40;//inDataEchange CODE
 dataTX[4] = 0x01;//Number of targets
 dataTX[5] = 0xA0;//Write Command
 dataTX[6] = address; //Address  

 for (int i = 0; i < 16; i++) {
  dataTX[i+7] = blockData[i];
 }

 dataTX[23] = 0x00;
 checkSum(dataTX);
 sendTX(dataTX , 24 ,14);  

 if ((dataRX[9]== 0xD5) & (dataRX[10] == 0x41) & (dataRX[11] == 0x00)) {
  return 0;
 } else {
  return 1;
 }
}
//**********************************************************************
//!Read 16 bytes from  address .
uint8_t readData(uint8_t address, uint8_t *readData) //!Reading
{
 Serial.print("                ");

 dataTX[0] = 0x05;
 lengthCheckSum(dataTX); // Length Checksum
 dataTX[2] = 0xD4; // Code
 dataTX[3] = 0x40; // Code
 dataTX[4] = 0x01; // Number of targets
 dataTX[5] = 0x30; //ReadCode
 dataTX[6] = address;  //Read address
 dataTX[7] = 0x00;
 checkSum(dataTX);
 sendTX(dataTX , 8, 30);
 memset(readData, 0x00, 16);  

 if ((dataRX[9]== 0xD5) & (dataRX[10] == 0x41) & (dataRX[11] == 0x00)) {
  for (int i = 12; i < 28; i++) {
   readData[i-12] = dataRX[i];
  }
  return 0;
 } else {
  return 1;
 }
}
//**********************************************************************
//!The PN532 sends back the version of the embedded firmware.
bool getFirmware(void)  //! It is needed to launch a simple command to sycnchronize
{
  Serial.print("                ");

 memset(dataTX, 0x00, 35);
 dataTX[0] = 0x02; // Length
 lengthCheckSum(dataTX); // Length Checksum
 dataTX[2] = 0xD4; // CODE
 dataTX[3] = 0x02; //TFI
 checkSum(dataTX); //0x2A; //Checksum   

 sendTX(dataTX , 5 , 17);
 Serial.print("\n");
 Serial.print("Your Firmware version is : ");

 for (int i = 11; i < (15) ; i++){
  Serial.print(dataRX[i], HEX);
  Serial.print(" ");
 }
 Serial.print("\n");
}

//**********************************************************************
//!Print data stored in vectors .
void print(uint8_t * _data, uint8_t length)
{
 for (int i = 0; i < length ; i++){
  Serial.print(_data[i], HEX);
  Serial.print(" ");
 }
 Serial.print("\n");
}
//**********************************************************************
//!This command is used to set internal parameters of the PN532,
bool configureSAM(void)//! Configure the SAM
{
 Serial.print("               ");

 dataTX[0] = 0x05; //Length
 lengthCheckSum(dataTX); // Length Checksum
 dataTX[2] = 0xD4;
 dataTX[3] = 0x14;
 dataTX[4] = 0x01; // Normal mode
 dataTX[5] = 0x14; // TimeOUT
 dataTX[6] = 0x00; // IRQ
 dataTX[7] = 0x00; // Clean checkSum position
 checkSum(dataTX);

 sendTX(dataTX , 8, 13);
}
//**********************************************************************
//!Send data stored in dataTX
void sendTX(uint8_t *dataTX, uint8_t length, uint8_t outLength)
{
 Serial.print(char(0x00));
 Serial.print(char(0x00));
 Serial.print(char(0xFF)); 

 for (int i = 0; i < length; i++) {
  Serial.print(char(dataTX[i]));
 }

 Serial.print(char(0x00));
 getACK();
 waitResponse();// Receive response
 getData(outLength);
}
//**********************************************************************
//!Wait for ACK response and stores it in the dataRX buffer
void getACK(void)
{
 delay(5);
 waitResponse();
 for (int i = 0; i < 5 ; i++) {
  dataRX[i] = Serial.read();
 }
}
//**********************************************************************
//!Wait the response of the module
void waitResponse(void)
{
 int val = 0xFF;
 int cont = 0x00;
 while(val != 0x00) { //Wait for 0x00 response
  val = Serial.read();
  delay(5);
  cont ++;
 }
}
//**********************************************************************
//!Get data from the module
void getData(uint8_t outLength)
{
 for (int i=5; i < outLength; i++) {
  dataRX[i] = Serial.read();//read data from the module.
 }
}
//**********************************************************************
//!Calculates the checksum and stores it in dataTX buffer
void checkSum(uint8_t *dataTX)
{
 for (int i = 0; i < dataTX[0] ; i++) {
  dataTX[dataTX[0] + 2] += dataTX[i + 2];
 }
 byte(dataTX[dataTX[0] + 2]= - dataTX[dataTX[0] + 2]);
}
//**********************************************************************
//!Calculates the length checksum and sotres it in the buffer.
uint8_t lengthCheckSum(uint8_t *dataTX)
{
 dataTX[1] = byte(0x100 - dataTX[0]);
}

https://www.cooking-hacks.com/documentation/tutorials/rfid-13-56-mhz-nfc-module-arduino-raspberry-pi-tutorial